Mustang GT Wheel Hop Fix: Best Kits for 2011+ Coyote Cars
Disclosure: Some links on this page go to retailers like Amazon and eBay. If you buy through them, we may earn a commission at no extra cost to you. See our affiliate disclosure.
If your Coyote Mustang shudders, bounces and chatters the rear tires on a hard launch, you have wheel hop. It feels awful, it kills your 60-foot time, and on a car with sticky tires it can break parts. The good news is that the right Mustang GT wheel hop fix is well known, fairly cheap compared with most power mods, and something a careful home mechanic can bolt on in an afternoon.
This guide covers why wheel hop happens and which parts actually fix it on each generation. Scope is 2011+ Coyote Mustangs only: the 2011-2014 S197 GT and Boss 302 with a solid rear axle, and the 2015-2023 S550 and 2024+ S650 with independent rear suspension (IRS). The two layouts hop for different reasons, so the fixes are different. Product facts come from BMR Suspension and Steeda pages we checked in October 2026. Prices move, so treat dollar figures as a ballpark.

Quick Answer: Best Mustang GT Wheel Hop Fix by Generation
| Your car | Start here | Next step if it still hops |
|---|---|---|
| 2015-2023 S550 GT and Bullitt (IRS) | IRS subframe (cradle) bushing lockout or support kit, such as the BMR CB005 or Steeda subframe support system | Subframe alignment dowels and braces, differential bushing inserts, better rear shocks |
| 2024+ S650 GT (IRS) | The same subframe lockout idea; BMR lists the CB005 for 2024-current cars and Steeda lists its Stop the Hop kit through 2026 | Differential bushing inserts, shocks, launch tuning |
| 2011-2014 S197 GT and Boss 302 (solid axle) | Boxed rear lower control arms with stiffer bushings | Lower control arm relocation brackets (especially on a lowered car), upper control arm and Panhard bar upgrades |
Our short version: on an S550 or S650, the subframe is the main problem, so a cradle lockout or support kit is the first Mustang GT wheel hop fix to buy. On an S197, flexy stamped lower control arms and soft bushings are the main problem, so start with the rear lower arms and add relocation brackets if the car is lowered. Not sure which generation you have? Our S197 vs S550 vs S650 guide breaks it down.
What Causes Wheel Hop on a Coyote Mustang?
Wheel hop is a cycle. The tire grabs, the suspension and bushings wind up under load, the tire loses grip and unloads, then it grabs again. That repeats many times a second, and you feel it as a violent shake from the rear of the car. Anything that lets the rear axle or subframe move around under torque feeds that cycle.
S550 and S650: the IRS subframe moves
Steeda explains it plainly on its Stop the Hop kit page: the factory IRS subframe mounts to the chassis at four locations with soft rubber bushings that have plenty of voids, even in the bolt holes. Under a hard launch the whole subframe, with the differential and half-shafts, can shift and rock. That movement is the main reason a 2015+ Mustang GT hops on sticky tires.
S197: the rear axle wraps up
The 2011-2014 car uses a solid axle located by two lower control arms, an upper third link, and a Panhard bar. The factory lower arms are stamped steel with soft rubber bushings, and they flex and deflect under load. Lowering the car makes it worse, because it changes the angle of the lower arms and the rear suspension geometry. The result is axle wrap, then hop.
Why you should fix it soon
- It costs you time. A car that hops cannot put power down, so the 60-foot time suffers no matter how much power you add.
- It is hard on parts. Owners report broken half-shafts, axles, and differential mounts from repeated hop, and the clutch and transmission take a beating too.
- It gets worse with grip. Drag radials and other sticky tires give the suspension more load to wind up, so hop often appears right after a tire upgrade.
Mustang GT Wheel Hop Fix for 2015+ S550 and S650 (IRS)
For the IRS cars, the fix is mostly about locking the subframe to the chassis so it cannot move. You can do that with inserts that fill the bushing voids, with lockout rings and braces, or with a full kit that also squares the subframe to the body.
BMR CB005 Cradle Bushing Lockout Kit (Level 2)
The BMR CB005 is one of the most popular S550 wheel hop parts. BMR lists it for 2015-2023 S550 and 2024-current S650 Mustangs. It uses 6061-T6 billet aluminum upper bushing lockout rings, stainless steel lower bushing support plates and washers, and cradle braces made from 1.625-inch DOM steel tubing. It is a 100% bolt-on design that installs over the factory rear cradle bushings, and BMR quotes a 1-2 hour install. BMR says it significantly reduces wheel hop without increasing NVH, and the braces add a solid rear jacking point on each side. In October 2026 BMR listed it at $199.95.
Convertible note: BMR says the CB005 is not compatible with convertible Mustangs unless you install it without the fore-end lower cradle braces. BMR also sells a simpler cradle bushing insert kit, the BK053, that fills the bushing voids with steel inserts.
Steeda Stop the Hop Street Starter Kit
The Steeda Stop the Hop Street Starter Kit bundles three parts: an IRS subframe alignment kit, Steeda’s IRS subframe bushing support system, and its IRS subframe support braces. Steeda says the alignment dowels are CNC-machined Delrin inserts that fill the factory bolt-hole voids and square the subframe to the chassis, limiting side-to-side and front-to-back movement. The bushing support system is an 8-piece billet 6061 aluminum kit with stainless hardware that fills the voids at the subframe mounts to stop up-and-down movement. The chrome-moly brace is a 5-point bolt-in part that ties the subframe to the chassis.
Steeda lists the kit for 2015-2026 Mustangs, rates the install as moderate with basic shop tools, and estimates about 3 hours. It lists the kit at $614.95. Like the BMR braces, Steeda says its IRS subframe support braces will not fit convertibles. You can also buy the three pieces separately and start with the bushing support system.
- Steeda Stop the Hop kit: Amazon · eBay
- Steeda IRS subframe alignment kit
- Steeda IRS subframe support braces
Differential bushing inserts
The rear differential also hangs on rubber bushings. Inserts or solid diff bushings stop the diff housing from rocking under torque. They are a common second step after the subframe is locked down, especially on cars with drag radials or a supercharger. Expect a little more gear noise in the cabin with solid parts.
- Mustang differential bushing inserts: Amazon
Vertical links and toe links
Rear vertical links and toe links get recommended a lot online. They are good parts for alignment and handling, but in our view they do much less for wheel hop than the subframe parts above. Buy them for alignment control on a lowered or track car, not as your main Mustang GT wheel hop fix.
- S550 Mustang rear vertical links
- S550 Mustang rear toe links

Mustang GT Wheel Hop Fix for 2011-2014 S197 (Solid Axle)
On the S197 Coyote cars, the fix is about controlling the rear axle. The lower control arms carry most of the launch load, so they come first, and relocation brackets correct the geometry if the car sits lower than stock.
Boxed rear lower control arms
Aftermarket lower control arms replace the stamped factory arms with boxed or tubular steel and stiffer bushings, usually polyurethane, spherical, or a mix. They cut flex and bushing deflection, which is a big part of what causes hop. Poly bushings are a good street choice. Spherical ends are stiffer and noisier and suit race cars. Adjustable arms let you set pinion angle and square the axle, which helps on a drag car. BMR, Steeda, UPR and others all make them.
- 2011-2014 Mustang GT rear lower control arms: Amazon
- BMR S197 anti-wheel hop package (lower arms + brackets)
Lower control arm relocation brackets
Relocation brackets give the rear of the lower arm new, lower mounting points on the axle. That restores a better arm angle on a lowered car, adds anti-squat, and helps the car plant the tires. Two well-known options work very differently:
| Bracket | Install | Key notes from the maker |
|---|---|---|
| BMR CAB005 relocation brackets | Bolt-on, no welding in all but extreme cases | Three mounting heights. BMR’s install sheet suggests the top hole for stock height to 1.00 in. lowered, middle for 1.00-1.75 in., bottom for more than 1.75 in. Stock arms may need modifying to use the upper positions. |
| Steeda 555-8119 relocation brackets | Weld-in, done on an alignment rack | Steeda says it is not recommended as bolt-in only and is not compatible with factory control arms. Its install sheet says the axle must be squared on an alignment rack before final welding. Steeda rates it hard, about 2 hours plus welding. |
For most street S197 GTs, a bolt-on bracket plus boxed lower arms is the practical choice. The Steeda weld-in brackets make more sense on a dedicated drag car going to a chassis shop anyway.
- BMR CAB005 control arm relocation brackets: Amazon · eBay
- Steeda lower control arm relocation brackets
Upper control arm, mount, and Panhard bar
The upper third link and its body mount also deflect under load, and an adjustable upper arm lets you set pinion angle. An adjustable Panhard bar keeps the axle centered on a lowered car. These are worth doing on an S197 that still hops after the lower arms, or on any car running drag radials hard.
- 2011-2014 Mustang adjustable upper control arm
- 2011-2014 Mustang adjustable Panhard bar

BMR vs Steeda for S550 and S650 Wheel Hop
| BMR CB005 (Level 2) | Steeda Stop the Hop Starter Kit | |
|---|---|---|
| What it is | Lockout rings, support plates and washers, plus cradle braces | Alignment dowels, 8-piece bushing support system, 5-point brace |
| Fitment listed | 2015-2023 S550 and 2024-current S650 | 2015-2026 Mustang (V6, EcoBoost, GT, Bullitt, GT500) |
| Install time (maker estimate) | 1-2 hours | About 3 hours, moderate |
| Convertibles | Only without the fore-end lower cradle braces | Subframe support braces will not fit |
| Price (Oct 2026) | $199.95 | $614.95 |
Our take: the BMR CB005 is the value pick and the one we would put on a street S550 or S650 first. The Steeda kit is the more complete package, since it also squares the subframe with dowels, and it suits cars with more power and sticky tires. Both makers claim no extra NVH. Some owners mix brands, but do not double up on braces: pick one brace design.
Tools Needed
These are general tools for subframe and control arm work. Always follow the maker’s instructions and torque values for your exact kit.
- Floor jack (low profile)
- Jack stands (pair): Amazon
- Metric socket set with 1/2 in. drive
- Metric combination wrench set
- Torque wrench (1/2 in. drive): Amazon
- Breaker bar
- Pry bar set
- Dead blow hammer
- Penetrating oil
- Medium strength threadlocker
- Transmission or utility jack (helpful for subframe work)
- Mechanic’s creeper
Parts Needed
Pick the parts for your generation. You do not need everything on this list.
2015+ S550 and S650 (IRS)
- BMR CB005 cradle bushing lockout kit (see our picks above)
- Steeda Stop the Hop kit (see our picks above)
- Steeda IRS subframe bushing support system
- Differential bushing inserts (see our picks above)
- Rear vertical links (optional)
- Rear toe links (optional)
2011-2014 S197 (solid axle)
- Rear lower control arms (see our picks above)
- BMR CAB005 relocation brackets (see our picks above)
- Adjustable upper control arm
- Upper control arm body mount
- Adjustable Panhard bar
For every car
- Drag radials or sticky rear tires
- Polyurethane bushing grease
- Rear shocks matched to your use
How to Install a Wheel Hop Kit (General Steps)
Every kit is different, so treat this as an overview, not a replacement for the instructions. If you are not comfortable supporting a car safely and working under it, have a shop do it. Most of these jobs are bolt-on, but the Steeda S197 brackets need welding.
- Read the instructions first. Check the parts list, the hardware, and the torque values before the car goes in the air.
- Lift and support the car safely. Use a level surface, chock the front wheels, and put the car on jack stands at the proper points. Never work under a car on a jack alone.
- Soak the old hardware. Spray penetrating oil on subframe or control arm bolts the night before if the car has seen salt or rain.
- Work one side or one mount at a time. On IRS cars, keep the subframe supported with a jack when bolts are loose. On S197 cars, swap one lower arm at a time so the axle stays located.
- Torque to spec at ride height. Many makers say to tighten suspension bushings with the car’s weight on the wheels so the bushings do not bind. Follow your kit.
- Get an alignment. Squaring the subframe or changing control arms can move the rear alignment. On an S197, check that the axle is square and the pinion angle is right.
- Recheck the bolts. Re-torque after a few hundred miles or after the first track day.
Tires, Shocks, Tune and Launch Technique
Hardware is only part of a Mustang GT wheel hop fix. These help just as much:
- Tires. Hop is often worst on worn summer tires that grab and let go. A real drag radial for the Mustang GT gives a softer sidewall that absorbs the shock of a launch instead of bouncing.
- Shocks. Worn or very soft rear shocks let the axle or subframe bounce. Good shocks are part of the fix. See our Mustang GT coilovers guide and lowering springs guide, and remember that too low hurts weight transfer on a drag car.
- Launch control and tune. A good Coyote tuner can set launch rpm and torque management so the car leaves without shock-loading the rear.
- Clutch and driver. On manual cars, dumping the clutch at high rpm is the fastest way to start hop and break parts. Our clutch upgrade guide covers what holds up to sticky tires.
- Gearing. Shorter rear gears multiply torque at the tires, so a car that was fine on factory gears may start hopping after a swap to 3.73s or 4.10s.
If the car still hops after the parts go in, lift off the throttle right away. Riding out hop is how half-shafts and axles break.
How Much Does a Mustang GT Wheel Hop Fix Cost?
In October 2026, the BMR CB005 listed at $199.95, the Steeda Stop the Hop Street Starter Kit at $614.95, the Steeda S197 weld-in relocation brackets at $229.95, and the BMR CAB005 bolt-on brackets at about $140 at a retailer. Add boxed lower arms for an S197 and expect a few hundred dollars more. A shop install and alignment adds labor on top. Rough totals are a few hundred dollars for a bolt-on IRS kit and roughly $400 to $1,000 or more for a full S197 rear setup with brackets, arms, and alignment. Prices change often, so check current listings.
Used suspension parts can be a good deal. Check bushings for cracks or wear, make sure all the hardware is there, and avoid bent or rusty arms.
Where This Fits in a Coyote Build
A wheel hop fix belongs early in any Coyote drag or street build, right after tires. In our 12-second build guide it sits alongside drag radials, and by the 11-second build it is a must. The full plan is in our Coyote Mustang drag build guide. Autocross and road course cars benefit too, since the subframe and axle also move on corner exit. Our street-class autocross build covers what is legal for SCCA Street class.
Mustang GT Wheel Hop Fix FAQ
What is the best Mustang GT wheel hop fix for an S550?
For most 2015-2023 S550 GTs, start with a subframe (cradle) bushing lockout or support kit such as the BMR CB005 or the Steeda Stop the Hop kit. Those parts stop the IRS subframe from moving, which is the main cause of hop on these cars.
Do the S550 wheel hop parts fit the 2024+ S650?
Some do. BMR lists its CB005 for 2015-2023 S550 and 2024-current S650 Mustangs, and Steeda lists its Stop the Hop Street Starter Kit for 2015-2026. Always check the maker’s fitment for your exact year and body style.
Will a wheel hop kit fit a Mustang GT convertible?
Check first. BMR says the CB005 only fits convertibles without the fore-end lower cradle braces, and Steeda says its IRS subframe support braces will not fit convertibles.
How do I fix wheel hop on a 2011-2014 Mustang GT?
Start with boxed rear lower control arms with stiffer bushings. If the car is lowered, add lower control arm relocation brackets to correct the arm angle. Upper control arm and Panhard bar upgrades help on harder-launching cars.
Does a wheel hop kit make the ride harsher?
BMR and Steeda both say their IRS subframe kits reduce hop without increasing NVH. Solid differential bushings and spherical control arm ends can add noise and vibration.
Bottom Line
The right Mustang GT wheel hop fix depends on the rear suspension under your car. On a 2015+ S550 or S650, lock down the IRS subframe first with a kit like the BMR CB005 or Steeda Stop the Hop, then add diff bushing inserts if you need more. On a 2011-2014 S197, start with boxed lower control arms and add relocation brackets if the car is lowered. Pair the parts with good tires, healthy shocks, and a smooth launch, and the Coyote will finally put its power down.
Featured photo: BWard 1997, CC BY 4.0, via Wikimedia Commons (cropped). Photo: Max Ronnersjö, CC BY-SA 3.0, via Wikimedia Commons (cropped).