Four used GT350 Voodoo camshafts laid on plastic sheeting, with cam phasers and timing sprockets on the ends

eBay Finds: GT350 Voodoo Camshafts With Phasers and Rockers

Disclosure: This post contains eBay and Amazon affiliate links. As an eBay Partner Network participant and Amazon Associate, this site may earn a commission from qualifying purchases at no extra cost to you. See our affiliate disclosure for details. We only feature 2011+ Coyote Mustang parts (S197 Coyote, S550, S650) from individual or small private sellers, not high-volume dealer warehouses.

Tuesday’s eBay Finds is a single lot for Shelby GT350 owners and anyone building a 5.2 Voodoo engine. A small seller in Groveport, Ohio, has a used set of GT350 Voodoo camshafts with the cam phasers still on them and two bags of rockers, for $400. Ford stamps these cams GR3E-6A273-AA and GR3E-6A270-AA, and both numbers show clearly in the photos. That’s a low price for factory 5.2 cams. But a lot of Coyote owners see “GT350 cams” and think of a cheap bolt-in upgrade for their 5.0, and that’s not what these are. So most of this post covers who these cams fit, why a cross-plane Coyote needs different cams, and what to ask before you buy. Nothing here has been in an earlier eBay Finds post. Prices were current when we checked on Nov. 3, 2026, and listings can sell or change at any time.

Listing ended? eBay listings sell or end fast. If a listing in this post has ended, see similar gt350 voodoo camshafts listings on eBay.

Used GT350 Voodoo Camshafts With Phasers and Rockers ($400)

Four used GT350 Voodoo camshafts laid on plastic sheeting, with cam phasers and timing sprockets on the ends
Photo: eBay seller 68ls1man. View listing ($400)
Ends of four used GT350 Voodoo camshafts, three showing bolted VCT phaser assemblies with timing sprockets
The phaser ends. Three phasers show in this shot. The fourth cam is turned the other way in the first photo, so confirm the phaser count with the seller.
Hand holding a camshaft with a data-matrix label and the stamped Ford part number GR3E 6A270 AA
The GR3E-6A270-AA stamp and data-matrix label on one of the cams.
Camshaft stamped GR3E-6A273-AA next to a data-matrix label, held just below the phaser and sprocket
The GR3E-6A273-AA stamp on another cam. Ask for the stamps on all four.
Two tied plastic bags full of used valvetrain rockers sitting on a cardboard box
Two bags of rockers come with the cams. Ask for a count and a close photo of the rollers.
  • Price: $400 (Buy It Now)
  • Condition: Used
  • Seller: 68ls1man (636 feedback, 100% positive), a small seller
  • Shipping: $60 USPS Ground Advantage from Groveport, OH, or free local pickup. No returns.
  • eBay item #: 206670937904

Why it’s worth a look

The 5.2-liter Voodoo in the 2015–2020 Shelby GT350 and GT350R is the flat-plane-crank member of the Coyote family, and its cams are a big part of why it revs so freely. This lot is a set of four used GT350 Voodoo camshafts with their phasers and two bags of rockers. The seller’s whole description is the two part numbers, GR3E-6A273-AA and GR3E-6A270-AA, and a note that the cams are in very nice shape and come with the rockers. Both numbers are stamped on the cam bodies next to data-matrix labels, and you can read them in the photos. There’s no mileage, no reason for removal and no photos of the lobes up close. The item specifics only say Ford, camshaft and made in the United States. For a sense of what new cams cost, Ford Performance lists its 5.2L High Performance Cams (M-6550-M52) at an MSRP of $2,160 for a set. Those aren’t the same part, as we explain below, but they show what a set of four Voodoo-head cams costs new. At $400 plus $60 shipping, this set costs a fraction of that, and the phasers and rockers come with it. Our take: for a GT350 owner who needs a spare set or a 5.2 builder who needs factory cams, this is a strong price if the lobes and journals check out.

Fitment notes

Fitment notes: These are factory cams for the flat-plane 5.2 Voodoo, so the natural home is a 2015–2020 Shelby GT350 or GT350R, or a Voodoo engine being rebuilt or swapped. They are not a bolt-in upgrade for a 5.0 Coyote. Every Coyote in a Mustang GT, from the 2011–2014 Gen 1 through the 2015–2017 Gen 2 and the 2018–2023 Gen 3, uses a cross-plane crank and a different firing order. The cam lobes on a factory GT350 cam are phased for the flat-plane firing order, so the valve events wouldn’t line up with the pistons in a cross-plane engine, and no tune fixes that. That’s why Ford Performance sells separate cross-plane cams for Coyote builds that run Voodoo heads (more on that below). The phasers and rockers bring their own questions. We couldn’t confirm from a Ford source whether the GT350 phasers interchange with any 5.0 Coyote phasers, and the rockers in this lot appear to be the GT350’s own roller finger followers, which Ford sells separately from the 5.0 parts. Our 2015–2023 Coyote Mustang hub covers the GT350 and the S550 GT side by side.

Questions to ask the seller

Start with the stamps. Ask the seller to photograph the part number on all four cams so you know you’re getting a complete set and not two of the same cam. Ask how many miles were on the engine, why the cams came out and whether the engine had any oil starvation, valvetrain noise or cam phaser codes before teardown. Ask for close-up photos of every lobe and bearing journal in good light, and of the phaser faces and the trigger wheel teeth. Find out whether all four phasers are included and whether any of them were locked out or replaced. Ask how many rockers are in the bags (a full engine uses 32) and whether they were kept in order. With no returns, get every answer in eBay messages before you buy, or use the free local pickup near Columbus and look the parts over in person.

Can you run GT350 Voodoo camshafts in a 5.0 Coyote?

Not the factory ones. This is the question that comes up every time a set of GT350 cams hits eBay, so here’s the short version of why, and what Coyote owners use instead.

Flat-plane vs. cross-plane firing order

The GT350’s flat-plane crank changes the order the cylinders fire in. Each cam lobe has to open its valve at the right moment for that order, so the factory Voodoo cams are ground for the flat-plane engine. A 5.0 Coyote fires in the standard cross-plane order. Drop GT350 cams in a Coyote and some valves would open at the wrong time for their cylinders. Cam phasers can only advance or retard a whole camshaft a limited amount. They can’t re-time individual lobes, and neither can a tune.

The Ford Performance route for Voodoo heads on a 5.0

Some builders do put GT350 cylinder heads on a cross-plane Coyote, and Ford Performance makes cams for exactly that. Its M-6550-M52 cam set is an intake and exhaust set for 2015–2017 5.2L heads, with 14 mm of lift and 270 degrees of duration on both. Ford says the set must be used with the 5.0 Gen 2 cam phasers, chains and crank sprocket, that it is meant for the standard 5.0 Coyote firing order, and that a custom calibration is required. Ford points Gen 1 builders to a separate M-6550-M52A version. Aftermarket cam makers such as GSC Power-Division also grind Voodoo-head cams with cross-plane lobe phasing. Builders on the big Mustang forums also report that Voodoo cams use a different base circle and their own roller finger followers, so mixing GT350 and 5.0 valvetrain parts takes careful checking. If you have a 2011–2014 car, our 2011–2014 Coyote Mustang hub covers the Gen 1 engine. Whatever cams you run, plan on a custom tune. Our best Mustang GT tuner guide covers the options.

Is a $400 set of GT350 cams worth it?

It depends on what’s under your hood. Here’s how we’d decide:

  • You own a GT350 or GT350R, or you’re rebuilding a 5.2 Voodoo: Worth a hard look. Factory cams, phasers and rockers for $460 shipped is cheap insurance or a cheap fix, as long as the lobes and journals look clean.
  • You have a 5.0 Coyote GT and want more top end: Pass. These factory cams are for the flat-plane engine. Look at cross-plane cams made for your generation instead.
  • The seller can’t show all four part numbers or close-ups of the lobes: Pass, or pick them up in person. With no returns, a scored lobe or a missing cam is your problem.

Our pick: a good-value set of factory GT350 Voodoo camshafts for the right buyer, and the wrong buy for a 5.0 owner chasing a cheap cam swap. If you’re building a 5.0 instead, our Coyote 5.0 build guide shows where cams fit in the order of upgrades, and our built Gen 2 Coyote engine find shows what a used engine with a cam story looks like.

Tips for buying used Coyote-family camshafts on eBay

Inspect before you install

Look at every lobe and journal under bright light. Pitting, scoring or a polished-through finish on a lobe means the cam is done. Spin each roller on the followers and feel for roughness. Keep used followers matched to the lobes they ran on if the seller kept them in order. Coat the lobes and journals with engine assembly lube before you install them.

Have the right tools for cam timing

Coyote-family engines need the cams locked in place while you tighten the phaser bolts. A Coyote camshaft holding tool set makes that much easier, and you’ll need a good 3/8-inch drive torque wrench for the phaser and cam cap bolts. Follow Ford’s service procedure for your engine, and replace any one-time-use bolts it calls for.

Protect yourself on a no-returns listing

  • Pay through eBay checkout so the Money Back Guarantee applies if the item arrives not as described. Skip any offer to pay outside eBay.
  • Don’t rely on the title for fitment. The stamped Ford part numbers are what count.
  • Ask for packing details. Cams are long and can bend or chip if they shift in a box.
  • If you’re near Columbus, Ohio, the free local pickup saves the $60 shipping and lets you check the parts before you pay.

Similar Posts

Leave a Reply

Your email address will not be published. Required fields are marked *